Opticover WiFi Extender Setup Guide

For your information: When you buy through links on Mesh Wifi Hub, we may earn a commission.

Are you searching for a step-by-step instruction on how to configure your new Opticover Wi-Fi extender? Look no further. If this is the case, you have arrived to the correct location.

WiFi routers of the most recent generation are capable of supplying you with an outstanding wireless network. Each of them, however, is limited by the range of their own networks. On top of that, there is the issue of interference, which is dependent on the configuration of your house.

The Opticover Wireless Extender is available in a variety of configurations. The Opticover N300, on the other hand, is the most well-known. This guide will make use of the N300 as an extension for the sake of the lesson. If you have another Opticover WiFi extender, you may use the same procedure as described here to configure it.

Opticover Wi-Fi Extender Wireless Network Setup

Ensure that the Opticover WiFI extender and your wireless router are compatible with one another before proceeding with the installation process. The Opticover WiFi extender is capable of supporting both single-band and dual-band networks. If your router is compatible with them, you should be set to go. In addition, the procedure of setting up your band is dependent on whatever band you choose to utilise.

Opticover provides users with three different types of connection options:

  • AP mode, also known as access point mode, is a mode of operation that allows you to connect to a network.
  • Repeater mode is activated.
  • Router mode is a mode of operation when a router is used.

With Opticover, you may connect to any router brand on the market with relative ease. You have two choices for how you want to approach the setup:

  • The WPS button is an option.
  • Option for logging into the web interface.

Let’s take a closer look at both of them.

By the conclusion of this lesson, you should be able to expand your Wi-Fi network with the help of the Opticover wireless range extender. In addition, the extender is compatible with almost any WiFi router on the market.

Opticover WiFi Repeater Extender Setup WPS Method

It is necessary to utilise the WPS technique if you do not want to enter complicated configurations and wish to begin using the Opticover WiFi repeater equipment as soon as possible.

It is a straightforward Do-It-Yourself(DIY) procedure.

First, you must remove the Opticover WiFi repeater from its packaging in order to begin using the procedure. Following the unboxing process, you must complete the instructions outlined below.

  • Connect the OptiCover WiFi repeater to a power source. You may utilise any power wall plug that is supported. In order to complete the configuration, you must plug in close to your WiFi router. It would be preferable if you also turned on the power from the right-hand side of the computer.
  • On the side of the WiFi extender, you will now discover a switch to change the mode.
  • From there, choose the Repeater mode from the drop-down menu.
  • After that, you must hold down the WPS button for a minimum of SIX seconds, or until the light flashes. The WPS will be activated as a result of this.
  • In order to complete the process, you must go to your Wi-Fi router and hit the WPS button on it.
  • Wait a little bit longer. It will take a few moments for the Opticover Wi-Fi extender to reboot, and after that, it will display steady lights, indicating that the connection has been established successfully. The signal is a consistent shade of green in colour.
  • Once the configuration is complete, it is time to move the Opticover extender to a more central location in order to improve the wireless network.

It is possible for the connection to fail in various circumstances. In such scenario, you must make certain that the Wi-Fi network is capable of receiving WPS signals before proceeding. Logging into the Wi-Fi router settings and enabling WPS if it is not already enabled will provide the necessary results.

Opticover WiFi Repeater Extender Web Interface Setup

It is necessary to utilise the WPS technique if you do not want to enter complicated configurations and wish to get started with the Opticover WiFi repeater equipment as soon as possible.

Do-It-Yourself(DIY) is a straightforward procedure.

Remove the Opticover WiFi repeater from its packaging before you may begin using the procedure. The following actions must be completed once the package has been opened.

Make sure to connect the OptiCover WiFi repeater to an electrical outlet. Almost any power wall socket that is supported may be used. Plugging in near your WiFi router will facilitate the setup. When turning on the power, it would be preferable if you did it from the right-hand side of the computer.

On the side of the WiFi extender, you will now discover a mode switch.

Switch to the Repeater mode after you’ve gotten to that point.

Now, you must hold down the WPS button for at least SIX seconds, or until the light flashes twice in rapid succession. As a result, the WPS will be activated.

Afterwards, you must go to your Wi-Fi router and hit the WPS button on it.

Please be patient. It will take a few moments for the Opticover Wi-Fi extender to reboot, and then it will display solid lights to indicate that the connection has been established successfully. The signal’s hue is a continuous shade of green throughout.

The Opticover extender should be placed in a more central location for a better wireless network once it has been properly configured.

It is possible for the connection to fail in various circumstances.. Then you’ll want to make sure that the Wi-Fi router is capable of accepting the WPS signal in that situation. Logging into the Wi-Fi router settings and enabling WPS if it is not already enabled will provide the necessary information.

Let’s get this show on the road by logging into the online interface. The procedures that you must follow are as follows:

  • Connect the Opticover extender to the power outlet using the included cable. Check to see if it is in close proximity to your primary Wi-Fi network.
  • Change the mode button to the repeating mode at this point.
  • From there, you must choose the Wi-Fi option on your laptop, mobile device, or desktop computer.
  • The default Wi-Fi SSID for the Opticover Extender may be found at this location.
  • Once you’ve established a connection, you may go to the web browser on your device.
  • From there, go to the Opticover login page by putting http://ap.setup or http://192.168.188.1 into your browser’s address bar.
  • After a little delay, the login page will appear. You will now need to log in using the username and password that can be found on the back of the Opticover to complete the process.

This will open up the status page for the Opticover. The status page will show information such as:

  • Firmware version
  • Uptime
  • Connection status
  • Wireless mode

At the very bottom, there’s a wizard menu for you to use. Afterwards, you’ll have to wait for it to repopulate the list of local WIFI networks. Your primary Wi-Fi router may be found on this list.

Connect to it by clicking on it and entering your Wi-Fi password. To allow the router and extender to connect, you must first input the password.

Setting the repeater SSID is next. You have complete control over which SSID repeater you use. A new Wi-Fi network SSID may be used in place of the previous one. “Connect” and the Save Settings button are the next steps.

This will cause the Wi-Fi router to restart. Restart it manually if it doesn’t work automatically.

You’ll be able to see the repeater’s status on the status page as soon as you’ve done this. If the light is solid green, the connection has been established.

Opticover Troubleshooting With Wireless Router

If anything goes wrong, you may be unable to connect the extension to your router. Because of this, you’ll have to do certain diagnostics in order to get it to operate.

  • In order to access the Opticover extender, you must ensure that the IP address is accurate.
  • A static IP address on the WiFi router should be avoided at all costs.
  • Be careful you use the right login and password when attempting to access the system.

If things are still not working, then maybe try to factory reset the wireless range extender. To reset, you need to use the following steps:

  • Power on the repeater by plugging it into the power socket
  • Once it is booted, you will find a small reset button on the repeater. It may also be a small hole depending on the model.
  • Now hold the reset button for a good 8-10 seconds. It will reset the lights. Once done, release it and wait for it to reboot. It can take anywhere between 2-3 minutes for it to reset to factory settings.

Read More: NEXTBOX WiFi Extender Setup

Conclusion

This brings us to the conclusion of our Opticover WiFi extender configuration. You should be able to appropriately setup your repeater if you follow the instructions provided here. Additionally, you may use the handbook that is supplied as a guide.

Franklin Lee
Franklin Lee
Articles: 88

Leave a Reply

Your email address will not be published. Required fields are marked *